The 7 Steps To Tiling Your Bathroom Like A Pro
Reproduced by kind permission of www.bathrooms-vanities.com
With an almost unlimited choice of patterns, textures and colours to please even the most fastidious tastes, bathroom tiles are the obvious choice for lining your bathroom or shower area. Although some people consider leaving it to the professionals, most bathrooms can be tiled in a weekend, even if you have had no previous tiling experience.
Before you begin, here are the essential tools you'll need for the job:-
Before you begin, it is imperative that the walls are clean, sound and dry. The surface should be as flat as possible and therefore you will need to remove any wallpapering and coat any flaking paint with a stabilizing primer. Now would be a good time to make your very own gauge stick, which will help you plot the position of the tiles on the wall. Find a piece of softwood and lay several tiles next to it (adding spacers if the tiles are square edged or butting together those with lugs) and mark off the position of each tile along the stick.
Setting Out The Tiles
The size and shape of your bathroom ultimately decides on how you set out the walls. Mark the bottom of the lowest row of tiles and temporarily nail a thin guide batten to the wall, aligned with the mark. Use the spirit level to ensure that this is perfectly horizontal. Marking the centre of the wall, use the gauge stick to set out the rows of tiles on each side of it. If the border tiles measure less than half the width of a tile, reposition the rows sideways by half a tile. Use the spirit level to place a guide batten against the last vertical line and nail it to the wall. If you have to tile around an object such as a window, use that as your starting point so that the surrounding tiles are of equal size. Cut tiles should be placed at the back of the window reveal. Again, use a temporary guide batten above the window to position the row of tiles above it.
It's important to always use a waterproof tile adhesive for areas that will come into contact with water. Most tile adhesives are sold ready-mixed, although some will require you to add water yourself. Apply the adhesive to the wall so that it covers about 1 metre square.
Using the toothed edge of the spreader, form horizontal ridges in the adhesive. Take the first tile and position it in the right angle formed by the setting out battens at the skirting level. If the tiles do not have lugs, place plastic spacers between them to ensure that there is enough space for the grouting.
Using a damp sponge, wipe away any adhesive from the surface of the tiles. Tile along the batten until the first rows are complete, ensuring that each tile is perfectly horizontal. When you are complete, allow the tiles to set before removing the battens.
Cutting The Border Tiles
Once you have completed the main area, the border tiles will need to be cut to fit the gap between the adjacent walls. Placing the border tile face down and with one edge next to the wall, mark where it is to be cut taking into consideration normal spacing between the tiles. Use a felt tip pen to transfer the mark to the face of the tile. Take the tile cutter and holding it against a straightedge, score across the face in one firm stroke. Stretching a length of thin wire across a panel of chipboard, place the scored line over the wire and press down on both sides to snap the tile. Alternatively, you can use a purpose-made tile-cutting jig. Using a tile sander, smooth over the cut edges of the tile.
When fitting tiles around a pipe, it's best to try and set them out so that you can cut a semi circle from the edges of two adjacent tiles. If this is not possible, mark the centre of the pipe on the top and side edges of the tile and draw lines across from these points. Using a coin, or something slightly larger than the diameter of the pipe, draw around where the two lines cross. Make a cut straight through the centre of the circle and then use a tile saw to cut out the remaining circle. To fit a tile against a curved shape, it's best to use a piece of thin card and draw a template of the exact size of the tile. Cut small, evenly spaced slits along one edge of the tile and press them against a curve replicate the shape. Transfer the gradient of the curve on to the face of the tile and then cut using a tile saw.
Grouting And Sealing
It is essential to use waterproof grout for any bath or shower surrounds. Grout comes in a pre-mixed paste grey, white or brown paste, although it is also possible these days to source coloured grouts that will blend in with your choice of tiles. Allow the tile adhesive to harden for 24 hours before applying the grout using a rubber-bladed spreader, ensuring that are the joints are filled. Using a sponge, wipe the grout from the surface of the tiles before it sets and smooth the joints with a blunt-ended stick. When it has dried, use a dry cloth to polish the face of the tiles and leave for about a week before using.
Sealing Bathroom Fittings
You should not use grout to seal the gap between the shower tray or bathtub and the wall, since it can crack and lose its waterproof seal. It's best to use a silicon sealant compound, which you can buy in cartridges. The sealants are again available in a choice of colours to match your choice of tile. Trim the end off the nozzle and press the tip into the joint at an angle of 45 degrees. When applying the sealant to bathtubs, it's best to stand in the bath* since the join will accommodate your body weight. When you have finished, smooth over any ripples with a wetted teaspoon handle.
* I have received the following useful observation from a visitor:-
May I make a suggestion to the item on tiling .Sub heading Sealing I go along with everything until it comes to the part about standing in the bath. when onegets out of the bath however the bath tub will rise slightly due to the weight being taken of the floor, then the silicone is squeezed out of the joints. What I do is fill the bath full of water. then silicone the joint, leave for 24 hours then let the water go, when the bath rises this time it compresses the dried silicone, whereas the other way every time the bath is filled the dried silicone is stretched leaving a damaged seal . I have done this for over 15 years and believe me it works the best of all.
Contributed by Alan Farrell
Good advice but there is a sealing strip you can buy to fit to the wall before you finish off around the bath, the same procedure with water in the bath and fit the seal in the adhesive of the row next to the bath for a water tight seal.
Copyright © 2000-2018 Hints and Things
Hints and Things cannot be held responsible for any information given on this site nor do they necessarily agree with, or endorse, the views given by third parties.